TITLE

Improvement of magnetic properties of an Fe-6.5 wt. % Si alloy by directional recrystallization

AUTHOR(S)
Zhang, Z. W.; Chen, G.; Bei, H.; Ye, F.; Chen, G. L.; Liu, C. T.
PUB. DATE
November 2008
SOURCE
Applied Physics Letters;11/10/2008, Vol. 93 Issue 19, p191908
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
We report that magnetic properties of an Fe-6.5 wt. % Si alloy can be improved through texture control by using directional recrystallization. Columnar grain structures with column sizes of ∼0.38×1.2 mm2 were developed during directional recrystallization. It was found that there are low energy boundaries between columns and main textures of the specimen were {110}<111> and {111}<110>. As a result, the coercivity of a directionally recrystallized specimen is reduced by a factor of 5 when measured along 60° away from the growth direction, as compared to a specimen consisting of ∼77 μm equiaxed grains.
ACCESSION #
35514283

 

Related Articles

  • A study of Cube grain nucleation in a commercial Al alloy during in-situ and discontinuous (ex-situ) annealing experiments. Sukhopar, Olga; Gottstein, Günter // Materials Science Forum;2014, Vol. 794-796, p1245 

    In the current study the nucleation of Cube grains during recrystallization in a commercial Al-Fe-Si alloy was investigated by in-situ and ex-situ annealing experiments at different temperatures. Both methods confirm that the Cube grains can be nucleated during RX both at large deformed Cube...

  • Effects of Mn and Cr Additions on the Recrystallization Behavior of Al- Mg-Si-Cu Alloys. Gongwang Zhang; Hiromi Nagaumi; Yi Han; Yi Xu; Parish, Chad M.; Tongguang Zhai // Materials Science Forum;2017, Vol. 877, p172 

    Upsetting tests on two newly developed Mn and Cr-containing Al-Mg-Si-Cu alloys with various Mn contents were carried out at a speed of 15 mm/s under upsetting temperature of 450 °C after casting and subsequent homogenization heat treatment using a 300-Tone hydraulic press. STEM experiments...

  • Mechanical Alloying and Spark Plasma Sintering of Nano-SiC Reinforced Al-12Si-0.3Mg Alloy. Abdullahi, Kachalla; Al-Aqeeli, Nasser // Arabian Journal for Science & Engineering (Springer Science & Bu;Apr2014, Vol. 39 Issue 4, p3161 

    Al-based commercial alloy Al-12Si-0.3Mg was pre-alloyed by mechanical milling technique with the addition of different concentrations of nano-SiC, i.e. 0, 5 and 12 wt%. This was done primarily to investigate the effect of SiC addition on the final morphology and alloys' characteristics. Spark...

  • Effect of Alloying Elements on the Colour Development of Anodised Al-Mg-Si Alloys. Senel, Esma; Hallenstvet, Merete // Materials Science Forum;2014, Vol. 794-796, p247 

    Colour of the anodised Al-Mg-Si alloys was quantified by spectrophotometric method defining L* (lightness), a* (greenness-redness) and b* (blueness- yellowness) values. All alloys exhibited yellow and green colour. The yellowness of the anodised surfaces increased significantly with the increase...

  • Dependence of photoconductivity on the dark Fermi level position in amorphous silicon alloys. Hack, M.; Guha, S.; Shur, M. // Applied Physics Letters;1984, Vol. 45 Issue 4, p467 

    We present results of a new model to describe the dependence of the room-temperature steady-state photoconductivity in amorphous silicon alloys upon the position of the dark Fermi level. This dependence is a consequence of both a change in the recombination path and dopant-created gap states. We...

  • Precipitation-hardening in cast AL–Si–Cu–Mg alloys. Tavitas-Medrano, F. J.; Mohamed, A. M. A.; Gruzleski, J. E.; Samuel, F. H.; Doty, H. W. // Journal of Materials Science;Feb2010, Vol. 45 Issue 3, p641 

    Age-hardenable aluminum–silicon alloys have attracted increasing attention in recent years, particularly as a result of the demand for lighter vehicles as part of the overall goal to improve fuel efficiency and to reduce vehicle emissions. Among these aluminum cast alloys, the 319-type...

  • Fabrication of Lotus-Type Porous Al-Si Alloys Using the Continuous Casting Technique. Park, J. S.; Hyun, S. K.; Suzuki, S.; Nakajima, H. // Metallurgical & Materials Transactions. Part A;Feb2009, Vol. 40 Issue 2, p406 

    Lotus-type porous Al-Si (4, 8, 12, 14, and 18 wt pct) alloys were fabricated using the continuous casting technique under a hydrogen gas pressure of 0.1 MPa at various transference velocities, and the effects of the silicon content level and transference velocity on the pore morphology and...

  • Effects of Processing Parameters on the Grain Refinement of Magnesium Alloy by Equal-Channel Angular Extrusion. Ding, S. X.; Chang, C. P.; Kao, P. W. // Metallurgical & Materials Transactions. Part A;Feb2009, Vol. 40 Issue 2, p415 

    The Mg-3 pct Al-1 pct Zn (AZ31) alloy has been used as a model material for understanding the grain-refinement process of a Mg alloy fabricated by equal-channel angular extrusion (ECAE). The effects of ECAE processing parameters on grain refinement have also been studied; it was found that these...

  • The Effect of Silicon Content on the Microstructure and Creep Behavior in Die-Cast Magnesium AS Alloys. Dargusch, M. S.; Bowles, A. L.; Pettersen, K.; Bakke, P.; Dunlop, G. L. // Metallurgical & Materials Transactions. Part A;Jun2004, Vol. 35 Issue 6, p1905 

    The effect of increasing levels of silicon on the microstructure and creep properties of high-pressure die-cast Mg-Al-Si (AS) alloys has been investigated. The morphology of the Mg2Si phase in die-cast AS alloys was found to be a function of the silicon content. The Mg2Si particles in castings...

Share

Read the Article

Courtesy of VIRGINIA BEACH PUBLIC LIBRARY AND SYSTEM

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics