TITLE

Spatially resolved strain measurements in Mo-alloy micropillars by differential aperture x-ray microscopy

AUTHOR(S)
Bei, H.; Barabash, R. I.; Ice, G. E.; Liu, W.; Tischler, J.; George, E. P.
PUB. DATE
August 2008
SOURCE
Applied Physics Letters;8/18/2008, Vol. 93 Issue 7, p071904
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
Spatially resolved strain distributions in the NiAl matrix and the ∼550–1000 nm Mo fibers of a NiAl–Mo eutectic were investigated by microbeam x-ray diffraction. Position sensitive d-spacings for the individual phases were obtained from spatially resolved and energy-resolved Laue patterns. For embedded Mo fibers, the measured elastic strain is consistent with the predicted thermal mismatch strain between the NiAl and Mo phases. However, when the NiAl matrix is etched back to expose Mo micropillars, the d-spacing increases to that of unconstrained Mo, indicating release of the compressive residual strain in the Mo fibers.
ACCESSION #
34135601

 

Related Articles

  • Measurement of strain in Al-Cu interconnect lines with x-ray microdiffraction. Solak, H.H.; Cerrina, F. // Journal of Applied Physics;7/15/1999, Vol. 86 Issue 2, p884 

    Reports on the measurement of strain in patterned aluminum-copper interconnect lines with x-ray microdiffraction technique with a micrometer spatial resolution. Determination of strain; Diffraction spot size analysis; Strain profile; Stress determination.

  • Influence of Growth Rate on Microstructural Length Scales in Directionally Solidified NiAl-Mo Hypo-Eutectic Alloy. Zhang, Jianfei; Ma, Xuewei; Ren, Huiping; Chen, Lin; Jin, Zili; Li, Zhenliang; Shen, Jun // JOM: The Journal of The Minerals, Metals & Materials Society (TM;Jan2016, Vol. 68 Issue 1, p178 

    In this article, the Ni-46.1Al-7.8Mo (at.%) alloy was directionally solidified at different growth rates ranging from 15 μm/s to 1000 μm/s under a constant temperature gradient (334 K/cm). The dependence of microstructural length scales on the growth rate was investigated. The results show...

  • Probing Martensitic Transition in Nitinol Wire: A Comparison of X-ray Diffraction and Other Techniques. Butler, J.; Tiernan, P.; Tofail, S. A. M.; Ghandi, A. A. // AIP Conference Proceedings;1/17/2011, Vol. 1315 Issue 1, p104 

    Martensitic to austenite transformation in Nitinol wire can be measured by a number of techniques such as XRD (X-Ray Diffraction), DSC (Differential Scanning Calorimetry), BFR (Bend and Free Recovery) and Vickers indentation recovery. A comparison of results from these varied characterisation...

  • Stress creation during Ni–Mn alloy electrodeposition. Hearne, Sean J.; Floro, Jerrold A.; Rodriguez, Mark A.; Tissot, Ralph T.; Frazer, Colleen S.; Brewer, Luke; Hlava, Paul; Foiles, Stephen // Journal of Applied Physics;3/1/2006, Vol. 99 Issue 5, p053517 

    The stress evolution during electrodeposition of NiMn from a sulfamate-based bath was investigated as a function of Mn concentration and current density. The NiMn stress evolution with film thickness exhibited an initial high transitional stress region followed by a region of steady-state stress...

  • X-Ray diffractometry of metamorphic nanoheterostructures. Galiev, G.; Pushkarev, S.; Klimov, E.; Maltsev, P.; Imamov, R.; Subbotin, I. // Crystallography Reports;Mar2014, Vol. 59 Issue 2, p258 

    Elastic strains in active regions of metamorphic transistor nanoheterostructures InAlAs/InGaAs/InAlAs on GaAs substrates with a metamorphic buffer (MB) having different complex designs have been determined by X-ray diffractometry. The objects of study are linear-graded MBs with different...

  • Texture Distribution and Plane Strain Mechanical Behavior of AA 7xxx Plates of Different Thicknesses. Becerra, Gonzalo; Ramos-Grez, Jorge; Montecinos, José // Journal of Materials Engineering & Performance;Nov2009, Vol. 18 Issue 8, p1144 

    Texture distribution of a rolled aluminum alloy type AA 7449 plate having two thicknesses is presented here. The mechanical behavior of these aluminum alloy plates under plane strain compression (PSC) was studied under different shear stress textures. Crystallographic texture of specimens was...

  • Synchrotron X-Ray Measurement and Finite Element Analysis of Residual Strain in Tungsten Inert Gas Welded Aluminum Alloy 2024. Preston, R. V.; Shercliff, H. R.; Withers, P. J.; Hughes, D. J.; Smith, S. D.; Webster, P. J. // Metallurgical & Materials Transactions. Part A;Dec2006, Vol. 37 Issue 12, p3629 

    Residual strains have been measured in a tungsten inert gas (TIG) butt-welded 2024 aluminum alloy plate using synchrotron X-ray diffraction. Novel two-dimensional strain maps spanning the entire plate reveal steep gradients in residual stress and provide detailed validation data for finite...

  • Photoreflectance spectroscopy of GaInSbBi and AlGaSbBi quaternary alloys. Kopaczek, J.; Rajpalke, M. K.; Linhart, W. M.; Jones, T. S.; Ashwin, M. J.; Kudrawiec, R.; Veal, T. D. // Applied Physics Letters;9/15/2014, Vol. 105 Issue 11, p1 

    Molecular beam epitaxy is used to grow Ga1− yInySb1− xBix (y ≤ 5.5% and x ≤ 2.5%) and Al y Ga1− ySb1− xBix alloys (y ≤ 6.6% and x ≤ 2.0%). The alloy composition and film thickness are...

  • Authors' Reply. Ranjan, M.; Tewari, R.; Van Ooij, W. J.; Vasudevan, V. K. // Metallurgical & Materials Transactions. Part A;Sep2005, Vol. 36 Issue 9, p2544 

    Discusses the changes on the understanding of the development of the interfacial layer in coatings produced in molten zinc-aluminum eutectoid alloy containing silicon. Target materials used in the X-ray diffraction (XRD) study; Information on the transmission electron microscopy investigation...

Share

Read the Article

Courtesy of VIRGINIA BEACH PUBLIC LIBRARY AND SYSTEM

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics