TITLE

CAMIN TEMPERLENMESİNDE ISITMA VE SOĞUTMA SÜREÇLERİNİN KARIŞIK SINIR ŞARTLARINDA SAYISAL MODELLENMESİ

AUTHOR(S)
Türkbaş, Selim; Ataer, Ö. Ercan
PUB. DATE
December 2007
SOURCE
Journal of the Faculty of Engineering & Architecture of Gazi Uni;Dec2007, Vol. 22 Issue 4, p727
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
A numerical method is presented for the simulation of the quenching of soda-lime silicate glass plate. The process consists of heating the glass to a temperature above 600 °C and cooling rapidly by air. Using one flux method the radiation source term of the glass is calculated. For one dimensional, unsteady heat conduction and radiation through the glass, the energy equation is solved using finite difference method. A program is written in FORTRAN and the temperature distribution in the glass plate is calculated. Results are given as diagrams and compared with the results given in the literature.
ACCESSION #
28652962

 

Related Articles

  • Numerical Study on Heat Transfer Deterioration of Supercritical n-Decane in Horizontal Circular Tubes. Yanhong Wang; Sufen Li; Ming Dong // Energies (19961073);2014, Vol. 7 Issue 11, p7535 

    In order to obtain a deeper understanding of the regenerative cooling process of scramjet engines, in this paper, a numerical investigation on the supercritical convective heat transfer of n-decane in horizontal circular tubes was conducted, based on a complete set of conservation equations and...

  • Numerical model of external heat exchange in a gas-electric glassmaking furnace. Dzyuzer, V.; Shvydkii, V.; Sadykov, E. // Glass & Ceramics;May2012, Vol. 69 Issue 1/2, p44 

    A concept for a mathematical model of a gas-electric glassmaking furnace is formulated. A system of equations for calculating external heat transfer is presented. The computational boundary conditions are examined.

  • Experimental and Numerical Analysis Applied on Steel Bars Cooling. Silva, Paul Campos Santana; Seixas, Paulo Henrique Terenzi; Rodrigues, Caroline; Fonseca, Leonardo; Huebner, Rudolf // Advanced Materials Research;2014, Vol. 1016, p342 

    AISI 1020 steel bars cooling have been investigated aiming to obtain their cooling rate during heat treatment. Hot steel bars just taken out of the furnace are piled over other ones that were taken out of the furnace earlier. A mathematical model has been created and implemented using the...

  • Numerical Study of the Effect of a Power Plant Cooling Water Discharge in the Montevideo Bay. Fossati, Mónica; Santoro, Pablo; Urrestarazu, Santiago; Piedra-Cueva, Ismael // Journal of Applied Mathematics;2011, Special section p1 

    The numerical simulation of the water temperature in the Río de la Plata River and Montevideo's Bay was done using the numerical model of finite elements RMA-10 in its 2D vertical integrated mode. Parameters involved in the formulations of thermal exchange with the atmosphere were adjusted...

  • A Study of Various Numerical Turbulence Modeling Methods in Boundary Layer Excitation of a Square Ribbed Channel. Saberinejad, Hojjat; Hashiehbaf, Adel; Afrasiabian, Ehsan // World Academy of Science, Engineering & Technology;Dec2010, Issue 48, p338 

    No abstract available.

  • Dependence of the width of the glass transition interval on cooling and heating rates. Schmelzer, Jürn W. P.; Tropin, Timur V. // Journal of Chemical Physics;1/21/2013, Vol. 138 Issue 3, p034507 

    In a preceding paper [J. W. P. Schmelzer, J. Chem. Phys. 136, 074512 (2012)], a general kinetic criterion of glass formation has been advanced allowing one to determine theoretically the dependence of the glass transition temperature on cooling and heating rates (or similarly on the rate of...

  • Analysis of the Parameters of an Electrothermal Induction System. Maş, Daniela; Leuca, Teodor; Nagy, Stefan; Mich-Vancea, Claudiu // Journal of Electrical & Electronics Engineering;Oct2011, Vol. 4 Issue 2, p65 

    This paper is aimed, based on MATLAB programming to emphasize the utility of using the analytical modeling in the design of the induction heating systems as the results may be used during the design and optimization process.

  • Modelling of a simple Dy doped chalcogenide glass fibre laser for mid-infrared light generation. Sujecki, S.; Sójka, L.; Bereś-Pawlik, E.; Tang, Z.; Furniss, D.; Seddon, A.; Benson, T. // Optical & Quantum Electronics;Jan2010, Vol. 42 Issue 2, p69 

    simple Dy-doped chalcogenide glass fibre laser design for mid-infrared light generation is studied using a one dimensional rate equation model. The fibre laser design employs the concept of cascade lasing. The results obtained demonstrate that efficient cascade lasing may be achieved in practice...

  • Experimental Tests of White UHPC Plates Reinforced by PVA Fibres and Textile Glass Reinforcement. BITTNER, Tomáš; TEJ, Petr; VOKÁČ, Miroslav; BOUŠKA, Petr; NENADÁLOVÁ, Šárka // Advanced Materials Research;2015, Vol. 1124, p83 

    The paper is dealing with the development of thin slabs made from white Ultra-High Performance Concrete (UHPC), which can be used as facade or roof panels. The slabs were designed with reinforcement realized by randomly dispersed polyvinylalcohol (PVA) fibres and a textile glass 2D net with mesh...

Share

Read the Article

Courtesy of THE LIBRARY OF VIRGINIA

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics