TITLE

Reactions of Chiller Maintain Efficiency

PUB. DATE
May 2006
SOURCE
Air Conditioning, Heating & Refrigeration News;5/1/2006, Vol. 228 Issue 1, p10
SOURCE TYPE
Trade Publication
DOC. TYPE
Article
ABSTRACT
The article offers information on the advantages of variable speed technology to users of industrial chillers as well as chiller manufacturers. Variable speed, when applied to a refrigeration compressor works to always fit the compressor output to the demand for cooling. The compressor always runs at the speed needed to deliver the cooling required to achieve the target temperature and no faster. Variable-speed compressors are also money-savers since they run all the time.
ACCESSION #
20954377

 

Related Articles

  • Variable-Frequency Drives. Tomczyk, John // Air Conditioning, Heating & Refrigeration News;10/5/2009, Vol. 238 Issue 5, p16 

    The article focuses on the significance of variable-frequency drives (VFD) in the creation of heating, air conditioning and refrigeration (HVACR) systems. It notes that systems with variable-speed fan motors can deliver variable air volume (VAV) flows to match the heating and cooling demands of...

  • Modulating Compressors For Residential Cooling. Roth, Kurt; Westphalen, Detlef; Dieckmann, John; Brodrick, James // ASHRAE Journal;Oct2004, Vol. 46 Issue 10, p56 

    The article reports that most residential air conditioners and heat pumps use a single compressor that operates at a single speed. Most of the time, however, the cooling or heating loads equal a fraction of a unit's full capacity, which causes the units to cycle on and off. Several approaches...

  • Report Looks at Worldwide Use of Chiller Technology.  // Air Conditioning, Heating & Refrigeration News;5/1/2006, Vol. 228 Issue 1, p10 

    The article reports that the Japan Air Conditioning Journal has given the Heating, Ventilation Air Conditioning and Refrigeration industry a feel for worldwide use of chiller technology and what types of chillers are being used. According to a report, the estimated number of centrifugal chillers...

  • Pre-Cooling Ventilation Outdoor Air, By Heat Exchange With Cooling Coil Condensate Discharge. Namek, Ramzi Y. // Engineered Systems;Mar2005, Vol. 22 Issue 3, p68 

    This article investigates energy efficient systems related to energy recovery and the geographic regions where it might prove beneficial. The cool condensate from a large air conditioning process may be collected and used to reduce the cooling load in an independent and smaller air conditioning...

  • No Sweat. Bonar II, Henry B. // Process Cooling & Equipment;May2004, p16 

    Focuses on desiccant dehumidification. Areas conducive to desiccant and reheat use; Advantages and disadvantages of desiccant dehumidification; Possibility of using desiccant technology with industrial refrigeration systems.

  • How to Efficiently Cool or Condense. Demakos, Peter // Process Cooling & Equipment;May2004, p18 

    Focuses on the usage of wet-surface air coolers for auxiliary fluid cooling and vapor condensing. Basic principle of operation; Air requirements; Maintenance and repair; Design specification; Water use and disposal issues.

  • We're on Deadline--Printing Press Heat Gain Is More (or Less) than Just Motor Load. Wessel, Dennis J. // ASHRAE Transactions;2004, Vol. 110 Issue 2, p871 

    Historically, heat gain from a newspaper printing press has been a conversion of input power to heat. This method of calculation has resulted in the installation of grossly oversized cooling equipment. Recently developed information from press vendors has resulted in the determination of...

  • CHAPTER 35: ICE RINKS.  // ASHRAE Handbook: Refrigeration;2006, p35.1 

    Chapter 35 of the book "2006 American Society of Heating, Refrigeration and Air-Conditioning Engineers Handbook (ASHRAE)-Refrigeration" is presented. It discusses the refrigeration requirements for ice rinks, as well as the conditions of ice rinks in relation to heating, ventilation, carbon...

  • Cooling Load Design Tool For UFAD. Bauman, Fred; Schiavon, Stefano; Webster, Tom; Kwang Ho Lee // ASHRAE Journal;Sep2010, Vol. 52 Issue 9, p62 

    The article presents an updated and more complete version of the cooling load design tools for underfloor air distribution(UFAD). It features the version 3.1 and the EnergyPlus, a publicly available whole building energy simulation program capable of modeling the more complex heat transfer...

Share

Read the Article

Courtesy of THE LIBRARY OF VIRGINIA

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics