TCS can prolong trailer landing gear life

June 2005
Trailer / Body Builders;Jun2005, Vol. 46 Issue 8, p65
Trade Publication
Presents information on the Telescopic Cross Shaft (TCS) from Cross Shaft Innovation Inc. Contribution of TCS to the elimination of compression stress in vehicles; Installation of TCS; Materials used in the cross shaft.


Related Articles

  • Linear Servomotor Replaces Piezo Motors.  // Medical Design Technology;Sep2011, Vol. 15 Issue 7, p7 

    The article offers brief information on the linear shaft motor from Nippon Pulse America Inc.

  • Service Tip. Redman, Roy // Journal of American Organbuilding;Sep2010, Vol. 25 Issue 3, p29 

    The article offers suggestions for sticking slider solenoids. It mentions that cleaning and lubricating the shaft will give a temporary relief from the problem. It notes that is possible to disassemble the Laukhuff solenoid through turning away the crimping on a lathe and by drilling out the...

  • Investigation of diesel generator shaft and bearing failures. Craighead, I.A.; Gray, T.G.F. // Proceedings of the Institution of Mechanical Engineers -- Part K;2004, Vol. 218 Issue 3, p153 

    A shaft failure in a 634 kW diesel generator after 4000 hours of operation required investigation, especially when similar sets began to show signs of excessive bearing housing wear. The failure was found to be due to torsional fatigue caused by operation at an unforeseen resonant condition. The...

  • SHIELDING BEARINGS: Grounding helps inverter-duty motors live up to their name. Willwerth, Adam // Motion System Design;Aug2012, Vol. 54 Issue 8, p20 

    The article offers information on the effectiveness of long-term shaft grounding for the potential savings of variable frequency drives (VFD)-driven designs. It is suggested that any motor without bearing protection that is to be used with a VFD should be equipped with a shaft grounding ring and...

  • SHORT-SHAFT ARTICULATED HEDGE TRIMMER.  // Arbor Age;Jul2005, Vol. 25 Issue 7, p18 

    The article presents information on the short-shaft articulated hedge trimmer Shindaiwa AHS2510. With an overall length of just 65 inches, the AHS2510 is ideal for trimming low hedges, brush, and ground cover. The AHS2510 employs an articulating gear case that rotates 130 degrees and has nine...

  • Grounding/monitoring ring with electrical bearing protection.  // Consulting-Specifying Engineer;Sep2015, Vol. 52 Issue 8, p68 

    The article evaluates the AEGIS iPRO-MR Ring shaft grounding and monitoring ring from Electro Static Technology.

  • Calculation of radial forces in smooth shaft slot seals. Melnik, V. // Chemical & Petroleum Engineering;Aug2011, Vol. 47 Issue 9/10, p603 

    A method based on determination of integral values of local pressure losses associated with potential flow velocity of a fluid in a smooth slot seal channel is proposed for calculating radial forces in slot seals in a case where the axes of the shaft and housing bushing of the seal assembly are...

  • Study of lateral-axial coupling vibration of propeller-shaft system excited by nonlinear friction. Jiang, Hao; Jiang, Weikang // Archive of Applied Mechanics;Aug2016, Vol. 86 Issue 8, p1537 

    Abnormal vibrations induced by the water-lubricated bearing-shaft friction will influence the normal operation of the propeller-shaft system. In order to study the influence of the friction effect on the axially loaded shaft system, a mathematical model of the coupled lateral and axial...

  • Ramsays cold forged components.  // Indian Textile Journal;Oct2009, Vol. 120 Issue 1, p134 

    The article features Ramsays Corp. Pvt. Ltd., manufacturer of cold forged components established in 1968. The company offers shafts and spindles as well as converts machined components into cold forged parts. The materials used by the original equipment manufacturer (OEM) supplier in its...


Read the Article


Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics