TITLE

Deconvoluting the influences of heat and plastic deformation on internal strains generated by friction stir processing

AUTHOR(S)
Wanchuck Woo; Hahn Choo; Brown, Donald W.; Bourke, Mark A. M.; Zhili Feng; David, Stan A.; Hubbard, Camden R.; Liaw, Peter K.
PUB. DATE
June 2005
SOURCE
Applied Physics Letters;6/6/2005, Vol. 86 Issue 23, p231902
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
Internal-strain profiles in friction-stir processed aluminum-alloy plates were investigated using neutron diffraction. Three different specimens were prepared with a purpose of separating the effects of frictional heating and severe plastic deformation on the internal-strain distribution: (Case 1) a plate processed with both stirring pin and tool shoulder, (Case 2) a plate processed only with the tool shoulder, and (Case 3) a plate processed only with the pin. The comparison between Cases 1 and 2 shows distinctly different strain profiles revealing deconvoluted effects of the different sources (i.e., heat, deformation, or the combination) on the internal strains generated during the friction-stir processing.
ACCESSION #
17328474

 

Related Articles

  • Texture and Structure Analysis of AluminumA-1050 using Neutron Diffraction Technique. Priyanto, T. H.; Suparno, N.; Setiawan; Muslih, M. R. // AIP Conference Proceedings;3/17/2008, Vol. 989 Issue 1, p85 

    Analysis of bulk aluminum A-1050 has been performed using FCD/TD-BATAN. From neutron diffraction pattern of bulk sample, two Bragg peaks, (220) and (200) are observed while three Bragg peaks of (111), (311) and (222) are over dumped. Due to preferred orientation, crystallites are highly oriented...

  • Measuring Inaccessible Residual Stresses Using Multiple Methods and Superposition. Pagliaro, P.; Prime, M. B.; Robinson, J. S.; Clausen, B.; Swenson, H.; Steinzig, M.; Zuccarello, B. // Experimental Mechanics;Sep2011, Vol. 51 Issue 7, p1123 

    The traditional contour method maps a single component of residual stress by cutting a body carefully in two and measuring the contour of the cut surface. The cut also exposes previously inaccessible regions of the body to residual stress measurement using a variety of other techniques, but the...

  • A friction model for dry contacts during metal-forming processes. Ramezani, Maziar; Ripin, Zaidi Mohd // International Journal of Advanced Manufacturing Technology;Nov2010, Vol. 51 Issue 1-4, p93 

    In a metal-working process, the friction between the material and the tools influences the process by modifying the strain distribution of the workpiece. This frictional behavior is often taken into account by using a constant coefficient of friction in the finite element simulations. However,...

  • Strain Mapping and Nanocrystallite Size Determination by Neutron Diffraction in an Aluminum Alloy (AA5083) Severely Plastically Deformed through Equal Channel Angular Pressing. Crespo, P. A. González; Pérez, C. Luis; Hughes, Darren J.; Turrillas, X. // Journal of Nanomaterials;2013, p1 

    Six specimens of an aluminum alloy (AA-5083) extruded by Equal Channel Angular Pressing following two different routes plus a blank sample were examined with a neutron radiation of 1.5448 Ã…. Macrostrain maps from the (311) reflection were obtained. A clear difference about accumulated...

  • In-Situ Neutron Diffraction Studies of Micromechanical Behavior in a Friction Stir Welded AA7475-T761. Liu, X.; Lin Peng, R.; Hofmann, M.; Johansson, S.; Wang, Y. // Metallurgical & Materials Transactions. Part A;Jan2011, Vol. 42 Issue 1, p89 

    n in-situ neutron diffraction technique was used to investigate the lattice strain distributions and micromechanical behavior in a friction stir welded (FSW) sheet of AA7475-T761. The neutron diffraction experiments were performed on the spectrometer for material research, STRESS-SPEC, at FRM II...

  • Residual Stresses in DC cast Aluminum Billet: Neutron Diffraction Measurements and Thermomechanical Modeling. Drezet, J.-M.; Evans, A.; Pirling, T. // AIP Conference Proceedings;5/4/2011, Vol. 1353 Issue 1, p1131 

    Thermally-induced residual stresses, generated during the industrial Direct Chill casting process of aluminum alloys, can cause both significant safety concerns as well as the formation of defects during down-stream processing. Although these thermally induced strains can be partially relieved...

  • Mechanical stress as a function of temperature for aluminum alloy films. Gardner, Donald S.; Flinn, Paul A. // Journal of Applied Physics;2/15/1990, Vol. 67 Issue 4, p1831 

    Presents a study that measured stress and reflectivity as a function of temperature in several alloys and layered aluminum films. Calculation of stress in layered films and multilayered films; Analysis of the stress behavior of aluminum and its alloys; Examination of stress in layered aluminum...

  • Experimental and numerical analysis of residual stress in cast aluminum alloy after FSP process. Węglowski, Marek Stanisław; Sedek, Piotr; Hamilton, Carter // Key Engineering Materials;2015, Vol. 651-653, p1563 

    The effect of FSP modification of cast aluminum alloy AlSi9Mg on residual stress are presented. The numerical results are compared with the residual stresses experimentally measured by the trepanation method. Experimental results show that the residual tensile stresses are higher on the...

  • Mechanical Tensioning of High-Strength Aluminum Alloy Friction Stir Welds. Altenkirch, J.; Steuwer, A.; Peel, M.J.; Withers, P.J.; Williams, S.W.; Poad, M. // Metallurgical & Materials Transactions. Part A;Dec2008, Vol. 39 Issue 13, p3246 

    The extent to which in-situ global mechanical tensioning (GMT) can be used to modify the residual stress state in friction stir (FS) welds is investigated in this article. Residual stress distributions have been determined by synchrotron X-ray and neutron diffraction for four sets of FS welds in...

Share

Read the Article

Courtesy of THE LIBRARY OF VIRGINIA

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics