TITLE

Electroconductive coatings on porous ceramic supports

AUTHOR(S)
Bladergroen, B.J.; Maluleke, A.; Linkov, V.M.
PUB. DATE
June 2003
SOURCE
Journal of Applied Electrochemistry;Jun2003, Vol. 33 Issue 6, p475
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
The preparation of porous conductive coatings on porous ceramic supports for potential use in electrosynthesis, anodic decomposition of organic compounds and electrosorption units is described. The prepared conductive coatings on porous ceramic supports consisted either of carbon, gold or nickel, or a combination of carbon and gold. Carbon coatings were obtained by pyrolytic decomposition of liquid petroleum gas (LPG), gold was sputter coated and nickel coatings were formed by electroless plating. The permeability for water and electrical resistance of each coated support were measured and compared. Pyrolytic carbon was deposited throughout the support whereas the nickel and gold coatings were formed on the outer surface of the support. The resistance of a carbon coating could be regulated between 0.5 and 2 à¡Ž cm-1 of support while the permeability of the carbonized support was as high as 75% of the permeability of the unmodified support. The nickel and gold coatings had no significant effect on the permeability and could be prepared with a resistance of 0.25 and 1 à¡Ž cm-1 of support, respectively.
ACCESSION #
16781762

 

Related Articles

  • Effect of Formation Conditions on Catalytic Properties of Self-Purifying Coatings. Stefanyuk, I. V.; Tavgen', V. V.; Shkadretsova, V. G.; Oleinikova, E. L.; Markevich, V. G.; Potronnikova, I. N. // Glass & Ceramics;May/Jun2003, Vol. 60 Issue 5/6, p190 

    It is found that the technological conditions for the formation of self-purifying coating depend on the sintering interval of the vitreous phase and its dispersion. The most porous coating with the maximum effect of self-purification (96 – 98%) was obtained on introducing 12 – 14...

  • Properties of Coatings Obtained in Treatment of Silicate Glasses in Potassium and Lead Nitrate Melts. Castacon, J. J. Torres; Gorokhovskii, A. V. // Glass & Ceramics;May/Jun2003, Vol. 60 Issue 5/6, p187 

    The effect of the duration of treatment of the surface of soda-lime glass in potassium and lead nitrate melts at a temperature of 460°C on the chemical and mechanical strength is investigated. It is demonstrated that the formation of a crystalline lead-silicate coating in this treatment...

  • High-Temperature Superconducting Paint.  // Physics Today;Oct88, Vol. 41 Issue 10, p106 

    This article features the paintable coating of the ceramic superconductor YBa2Cu3O7-x form ZYP Coatings. The coating is produced with a nonaqueous, non-contaminating medium, yielding a water-resistant coating of 1-2- superconductive ceramic when it dries. Applications include fired-on...

  • Light losses in sol-gel coatings. Atkarskaya, A. // Glass & Ceramics;Jan2008, Vol. 65 Issue 1/2, p44 

    It is shown that the translucence of a substrate strongly influences light transmission by glass articles modified by sol-gel coatings. In contrast to glass, where light scattering is proportional to the refractive index, an inverse proportionality has been found in the films studied, which can...

  • Nominations Sought for the Roy W. Tess Award.  // Paint & Coatings Industry;Aug2006, Vol. 22 Issue 8, p12 

    The article reports that the Division of Polymeric Materials: Science and Engineering of the American Chemical Society, is in search for nominees for the 2007 Roy W. Tess Award in Coatings. The award is designed to honor the achievements and contributions to coatings science, technology and...

  • Rheological Model and Mechanical Properties of Hard Nanocoatings in Numerical Nanoindentation Test. Kopernik, M.; Pietrzyk, M. // AIP Conference Proceedings;2007, Vol. 907 Issue 1, p659 

    The objective of the work is development of the method, which is based on inverse analysis principles, and which allows determination of material model for lower material layer in the hard nanocoatings system. Hardness of such a system is additionally calculated in the paper. Design of block...

  • Study of functional coating preparation on ceramic materials. Suzdal'tsev, E.; Kharitonov, D.; Anashkina, A. // Refractories & Industrial Ceramics;Jan2012, Vol. 52 Issue 5, p340 

    Results are presented for a study of functional coating application, for example with increased blackness coefficient, on ceramic and glass ceramic materials. Various methods for coating application used currently are considered. A coating is proposed based on methyl phenyl spirocyloxane polymer...

  • Electrocoat clinic. Jacob, Ron // Products Finishing;Dec2005, Vol. 70 Issue 3, p30 

    The article presents the author's answers to various questions related to electrocoat processes. When a reader asks question about the pretreatment of zinc plated prior to cathodic electrocoating, the author replies that the zinc phosphate will work much better if the clear is eliminated,...

  • The reactivity with uranium of coating layers by the thermal spraying method. Cho, Choon-ho; Lee, Yun-sang; Kim, Eung-soo; Kim, Jeong-guk; Lee, Han-soo // Journal of Radioanalytical & Nuclear Chemistry;Feb2011, Vol. 287 Issue 2, p485 

    The uranium ingot casting process is one of the steps which consolidate uranium deposits produced by electrorefiner in an ingot form in a pryprocessing technique. Since molten uranium metal reacts with a graphite crucible when the uranium is being dissolved, a graphite crucible cannot be used....

Share

Read the Article

Courtesy of THE LIBRARY OF VIRGINIA

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics