TITLE

An inkjet-printed chemical fuse

AUTHOR(S)
Mabrook, M. F.; Pearson, C.; Petty, M. C.
PUB. DATE
January 2005
SOURCE
Applied Physics Letters;1/3/2005, Vol. 86 Issue 1, p013507
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
Inkjet printing of the conductive polymer poly(3,4-ethylene dioxythiophene) doped with polystyrene sulfonated acid has been used as the basis for a sensor for organic vapors. The electrical resistance of the film was monitored as it was exposed to atmospheres containing alcohol. Ultrathin films exhibited a sharp and nonreversible increase in their resistance. This resulted from a change in the morphology of the organic layer, thereby disrupting the current flow through the polymer. An intended application for these inkjet-printed devices is in disposable handheld instruments to monitor the presence of organic vapors above a threshold level.
ACCESSION #
15593114

 

Related Articles

  • Deposition of PEDOT: PSS Nanoparticles as a Conductive Microlayer Anode in OLEDs Device by Desktop Inkjet Printer. Ummartyotin, S.; Juntaro, J.; Wu, C.; Sain, M.; Manuspiya, H. // Journal of Nanomaterials;2011, p1 

    A simple microfabrication technique for delivering macromolecules and patterning microelectrode arrays using desktop inkjet printer was described. Aqueous solution of nanoparticle of poly (3,4-ethylenedioxythiophene) (PEDOT) doped with polystyrene sulfonic acid (PSS) was prepared while its...

  • Dual phase continuity and phase inversion phenomena in natural rubber/ethylene vinyl acetate (EVA) copolymer blends. Kaewsakul, Wisut; Kaesaman, Azizon; Nakason, Charoen // e-Polymers;Jan2012, Issue 1-25, p1 

    Blending of polymers provide an attractive route to obtain new materials with unique combination of properties. Among the possible blend morphologies are dispersion of droplet, fiber, lamella in continuous phase and cocontinuous morphology. The unique feature of co-continuous is the mutual...

  • Polymer bilayer structure via inkjet printing. Yajun Xia; Friend, Richard H. // Applied Physics Letters;4/17/2006, Vol. 88 Issue 16, p163508 

    We report the formation of a polymer bilayer structure by inkjet printing poly(9,9′-dioctylfluorene-co-benzothiadiazole) (F8BT) from p-xylene solution onto a poly(9,9-dioctylfluorene-co-N-(4-butylphenyl)diphenylamine (TFB) thin film. Despite the compatibility of both polymers with the same...

  • In Situ Electrical And Raman Investigations Of Inkjet-Printed PEDOT:PSS Layers. Paez-Sierra, Beynor Antonio; Padinger, Franz // AIP Conference Proceedings;8/6/2010, Vol. 1267 Issue 1, p691 

    The article reports on a study related to the Raman and in situ electrical analysis of inkjet printed polymer Poly 3,4-ethylenedioxythiophene poly styrenesulfonate (PEDOT: PSS) layers. The authors of the study used it as the transparent electrical contact for improving the hole injection...

  • Study on electrohydrodynamic jetting performance of organic solvents. Lee, Soo-Hong; Nguyen, Xuan; Gim, Yeonghyeon; Ko, Han // Journal of Mechanical Science & Technology;Nov2015, Vol. 29 Issue 11, p4767 

    The electrohydrodynamic (EHD) inkjet method is a printing technology using electricity. This technique allows for the printing of EML (Emission layer) materials, usually used for OLED devices, on a substrate. In this study, ejection experiments were performed with various solvents to verify...

  • Low-cost fabrication of submicron all polymer field effect transistors. Wang, J. Z.; Gu, J.; Zenhausern, F.; Sirringhaus, H. // Applied Physics Letters;3/27/2006, Vol. 88 Issue 13, p133502 

    All polymer field effect transistors have been fabricated combining nanoimprint lithography and inkjet printing. Trenches with hydrophilic bottoms confined by hydrophobic walls with considerable height are patterned by nanoimprint lithography. Conducting polymer solutions were then delivered...

  • MEATJET PRINTING.  // APC (Bauer Media Group);May2006, Vol. 26 Issue 5, p133 

    The article presents information on the meatjet printing. The scientists from the Medical University of South Carolina and Clemson University have developed a way to use the common inkjet printer to create 3D biological structures. The printer sprays cells onto moulds pre-built in a...

  • Thermal Annealing Effect on the Morphology of Inkjet Printed Polymer:Fullerene Composites Solar Cells. Fauzia, V.; Umar, A. A.; Salleh, M. M.; Yahaya, M. // Acta Physica Polonica, A.;Jan2012, Vol. 121 Issue 1, p155 

    One of critical factor in determining the performance of solar cells is the morphology of the active layer. The drying process of the active layer prepared by inkjet printing technique plays a key role in obtaining high quality surface morphology. This paper reports the effect of thermal...

  • A New Method for Reproducing Oil Paintings Based on 3D Printing. Chen Chen; Chen Guangxue; Yu Zhaohui; Wang Zhaohui // Applied Mechanics & Materials;2014, Issue 644-650, p2386 

    This work aims at presenting a new method for reproducing oil paintings via 3D printing. We used a laser scanner to detect the surface morphology of an oil painting and found it was capable to print the stereo brushstrokes through layered printing after analyzing the UV ink thickness of type...

Share

Read the Article

Courtesy of THE LIBRARY OF VIRGINIA

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics