TITLE

Effect of N+ ion implantation on the corrosion behaviour of Ti–6Al–7Nb and Ti–5Al–2Nb–1Ta orthopaedic alloys in Hanks solution

AUTHOR(S)
Lakshmi, S. Gokul; Tamilselvi, S.; Rajendran, N.; Arivuoli, D.
PUB. DATE
March 2004
SOURCE
Journal of Applied Electrochemistry;Mar2004, Vol. 34 Issue 3, p271
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
Ti-6A1-7Nb and Ti-5A1--2Nb-1Ta alloys were implanted with N+ ions with an ion energy of 75 keV at a dose rate of 1 x 1017 and 1 x 1018 ions cm-2. Open circuit potential (OCP) and potentiodynamic cyclic polarization measurements were carried out on the titanium alloys in Hanks solution to assess their corrosion resistance. The tendency for repassivation is higher in the case of implanted alloys than in untreated alloys owing to the formation of stable passive films. The impedance data showed a decrease in the double layer capacitance and an increase in the charge transfer resistance of the treated alloys. Nitrogen ion implanted Ti-6A1-7Nb was found to be more corrosion resistant than implanted Ti-S Al-2 Nb-i Ta alloy.
ACCESSION #
15102846

 

Related Articles

  • The Effect of α Phase on the Deformation Mechanisms of β Titanium Alloys. Jaworski Jr., A.; Ankem, S. // Journal of Materials Engineering & Performance;Dec2005, Vol. 14 Issue 6, p755 

    The effects of α and β phase interactions on the tensile and creep deformation behavior of β titanium alloys was studied using Ti-6.0wt.%Mn and Ti-8.1wt.%V as the model two-phase alloys, and Ti-13.0wt.%Mn and Ti-14.8wt.%V as the single-phase β alloys. The β phase of...

  • Quick Reference Guide for β Titanium Alloys in the 00s. Nyakana, S. L.; Fanning, J. C.; Boyer, R. R. // Journal of Materials Engineering & Performance;Dec2005, Vol. 14 Issue 6, p799 

    Beta titanium alloys provide useful combinations of physical and mechanical properties, as well as a wide range of processing options and generally good corrosion properties. Throughout the past several decades, many β alloys have been researched, yet only a handful of these currently enjoy...

  • TRAPPING - DETRAPPING MODEL FOR NITROGEN DISTRIBUTION IN NITRITED CoCr ALLOYS. Petraitienė, Akvilė; Galdikas, Arvaidas // International Conference: Radiation Interaction with Material & ;2012, p173 

    The nitrogen depth profile in CoCr alloys after plasma nitriding at temperatures 350-445°C is analyzed by the "trapping - detrapping" model. The model considers diffusion of nitrogen under the influence of trap sites formed by local chromium atoms. Nitrogen depth profiles were fitted by the...

  • Analisys of Corrosion Behavior of Ti-15Mo Alloys. Nava-Dino, C. G.; Bautista-Margulis, R. G.; Neri-Flores, M. A.; Orozco-Carmona, M. V.; de la Torre, S. D.; Gonzalez-Rodriguez, J. G.; Chacon-Nava, J. G.; Martínez-Villafañe, A. // International Journal of Electrochemical Science;2012, Vol. 7 Issue 5, p4250 

    The Ti-15Mo alloys have been studied by using electrochemical measurements. The electrochemical test was made to analyze their resistance and predictability to corrosion from green dust samples, SPS samples and arc-melt alloying. The corrosion behavior in Ringer's solution was evaluated by...

  • Superelasticity in β Titanium Alloys with Nitrogen Addition. Furuhara, T.; Annaka, S.; Maki, T. // Journal of Materials Engineering & Performance;Dec2005, Vol. 14 Issue 6, p761 

    Deformation behavior at room temperature was examined in near-β titanium alloys, Ti-10V-2Fe-3Al, containing small amounts of N up to 0.2 mass%. After a β solution treatment, thermally induced α″ martensite is formed in the N-free alloy but no martensite is formed in the 0.1 and...

  • INFLUENCE OF ION IMPLANTATION ON OXIDATION BEHAVIOR OF TiAl. YOSHIHARA, MICHIKO; TANIGUCHI, SHIGEJI // International Journal of Modern Physics B: Condensed Matter Phys;10/30/2006, Vol. 20 Issue 25-27, p4667 

    The influence of alloying elements on oxidation behavior of TiAl has been investigated using an ion-implantation technique and the mechanisms were discussed. The influence can be classified into several groups according to their effects. The implantation of β-forming elements, halogens, Cu...

  • Investigation of the weldability of titanium alloys produced by different methods of melting. Akhonin, S.; Mishchenko, R.; Petrichenko, I. // Materials Science;May2006, Vol. 42 Issue 3, p323 

    We study the influence of the method of melting of the metal (vacuum-arc and electron-beam melting with an intermediate tank) on the properties and weldability of titanium alloys. We show that the weldability of VT1-0 and VT6 alloys is practically independent of the method of their melting.

  • Effect of hydrogen on phase and structural transformations in titanium alloys of different classes. Il’in, A.; Skvortsova, S.; Mamonov, A.; Kollerov, M. // Materials Science;May2006, Vol. 42 Issue 3, p316 

    We study the laws of phase and structural transformations in titanium alloys under the action of dissolved hydrogen and in the course of subsequent degassing. We show the possibility to control structure formation in them with the help of alloying with hydrogen and to obtain structures that...

  • Structure and properties of high-modulus alloys of the Ti-B system. Firstov, S.; Kuz’menko, M.; Kulak, L.; Kotko, A.; Koval’, O.; Horna, I. // Materials Science;May2006, Vol. 42 Issue 3, p309 

    We study the influence of alloying with Al, Zr, and Si on the structure and mechanical properties (including the modulus of elasticity) of cast and deformed alloys of the Ti-B system. It is shown that, by optimizing the compositions of titanium alloys subjected to combined silicoboride hardening...

Share

Read the Article

Courtesy of THE LIBRARY OF VIRGINIA

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics