TITLE

Oribital Weld Heads Designed for Limited Access Applications

PUB. DATE
October 2004
SOURCE
Welding Journal;Oct2004, Vol. 83 Issue 10, p20
SOURCE TYPE
Periodical
DOC. TYPE
Article
ABSTRACT
Features Orbimatic GmbH's Orbiweld S series slim-line weld heads designed for welding closely packed stainless steel tubes and fittings in pipeline systems. Inclusion of water-cooling channels around the weld head body.
ACCESSION #
14712900

 

Related Articles

  • Weldability Evaluation of Supermartensitic Stainless Pipe Steels. Ramirez, J. E. // Welding Journal;May2007, Vol. 86 Issue 5, p125s 

    The article discusses a study on the weldability evaluation of supermartensitic stainless pipe steels and their susceptibility to hydrogen-induced stress corrosion and the influence of short postweld heat treatment. The results showed that the filler metal and welding procedure combination...

  • Study of Local Stresses and Strains in Welded Joints of Steel 03Kh17N9M3 Pipe Fittings by Computer Modeling Methods. Bilenko, G. // Metallurgist;Jul2015, Vol. 59 Issue 3/4, p271 

    An analysis is made of local residual stresses in an annular weld formed on two pipes of steel 03Kh17N9M3. The weld was made by orbital welding with a non-fusible electrode in protective gases. The welding operation was studied by computer modeling with the use of the finite-elements method.

  • Historic Welding Project Now Declassified. Disney, J. A. // Welding Journal;Jun2007, Vol. 86 Issue 6, p54 

    The article highlights a wealth of stainless steel pipe welding information released by the U.S. Department of Energy's (DOE) declassification of historical paperwork associated with the Hanford Project. The challenges faced in building the reduction and oxidation separation process (REDOX) and...

  • The Influence of Molybdenum on Stainless Steel Weld Microstructures. Anderson, T. D.; Perricone, M. J.; DuPont, J. N.; Marder, A. R. // Welding Journal;Sep2007, Vol. 86 Issue 9, p281 

    The article proposes a method of producing austenitic welds that can potentially avoid the difficulties normally encountered when fusion welding superaustenitic stainless steel. The method involves the design of fusion zone compositions that exhibit a primary ferrite solidification mode and...

  • Interpretation of Phase Formation in Austenitic Stainless Steel Welds. Iamboliev, T.; Katayama, S.; Matsunawa, A. // Welding Journal;Dec2003, Vol. 82 Issue 12, p337-S 

    Discusses the mechanism of microstructure formation in austenitic stainless steel welds. Criteria for identification; Solidification modes under arc welding conditions.

  • Influence on Pitting Corrosion Behavior of Welded AISI30400 Plate in a Freeze-Thaw Environment. Tsuyoshi TAKAHASHI; Yoshitaka IWABUCHI; Kazunori ISHITSUKA; Keita MURAKAM // Applied Mechanics & Materials;2014, Issue 590, p307 

    Welded structures which set up in outdoor in snow- and cold-prone areas are exposed to severe environment, in which liquids containing CI- chloride ions from the sea breeze and snow melting agents undergo freeze-thaw cycles during the winter. CI- solutions are known to produce pitting corrosion...

  • Copper Contamination Cracking in Austenitic Stainless Steel Welds. Rao, Sanyasi; Al-Kawaie, Ali Y. // Welding Journal;Feb2010, Vol. 89 Issue 2, p46 

    The article discusses the leakage of a newly installed austenitic stainless steel piping joints during a precommissioning hydrotest and low-pressure air leak test. It mentions that the piping system used ASTM A312 Grade TP316L pipes, and was part of a recovery project for natural gas liquids...

  • Good Practices for Inspecting Austenitic Stainless Steel Tube and Pipe Systems in Hygienic Applications. Lang, Michael // Inspection Trends;Apr2013, Vol. 16 Issue 2, p19 

    The article provides tips for U.S. welding inspectors on checking austenitic stainless steel tube and pipe systems in hygienic applications, in compliance to the American Welding Society (AWS) D18.1/D18.1M specification. Welding inspectors are required to verify preconstruction weld sampling...

  • Pipe Dream. Lowar, Bill // Processing (08968659);Oct2011, Vol. 24 Issue 10, p40 

    The article discusses various methods to join stainless steel pipes and mentions pros and cons related to them. It elaborates different joining methods including welding, flaging and threading. It is stated that welding is a dangerous activity because it involves heat flame and sparks. Problems...

Share

Read the Article

Courtesy of THE LIBRARY OF VIRGINIA

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics