Electrosynthesis of Mg(OH)2 Coatings on Stainless Steel Substrates

Dinamani, M.; Kamath, P. Vishnu
September 2004
Journal of Applied Electrochemistry;Sep2004, Vol. 34 Issue 9, p899
Academic Journal
Cathodic reduction of aqueous solutions of Mg(NO3)2 results in the deposition of Mg(OH)2 coatings on stainless steel cathodes. The coating growth is controlled by varying the deposition time, current density and the bath concentration. The coatings comprise thin scaly particles having sub-micron dimensions. DIFFaX simulations of the X-ray line broadening indicate the formation of small anisotropic particles having a thickness 134 Ã… measured along the [0 0 1] direction.


Related Articles

  • POWDER COATING CLINIC. Liberto, Nick // Products Finishing;Apr2008, Vol. 72 Issue 7, p58 

    The article presents questions and answers related to powder coating including the slight discoloration of a stainless steel hardware after powder coating, solutions for the mitigating of leaching the colors of electrical wirings, and information concerning virgin deionization water.

  • POWDER COATING CLINIC. Liberto, Nick // Products Finishing;Mar2007, Vol. 71 Issue 6, p66 

    The article presents questions and answers related to powder coating in the U.S. A customer powder coater asks some advice about switching from e-coat to powder coat on his zinc parts and how to assure that these zinc parts will have adequate and consistent adhesion. Another seeks for advice on...

  • Tray with preinstalled splice.  // Cabling Installation & Maintenance;Mar2006, Vol. 14 Issue 3, p61 

    The article evaluates the FCF 54 FASCLIC tray from Cablofil Inc. and offers information on lightweigh cable runs, on site fabrication, and electrozinc and stainless steel finishes.

  • Deposition Features of Ti Coating Using Irregular Powders in Cold Spray. Yin, Shuo; He, Pengjiang; Liao, Hanlin; Wang, Xiaofang // Journal of Thermal Spray Technology;Aug2014, Vol. 23 Issue 6, p984 

    The investigation on the deposition features of irregular Ti powders coated on Al and stainless steel (SS) substrates was conducted in this study. Ti coating was experimentally produced at different gas inlet temperatures, and then detailed analysis on the critical velocity, coating...

  • Electrical Properties of High Temperature Insulation Coatings under various Pressures at 298 K and 77 K. Cakiroglu, O.; Arda, L. // AIP Conference Proceedings;2007, Vol. 899 Issue 1, p431 

    The high temperature insulation coatings were prepared using solution of Mg and Zr based precursors. Then the MgO-ZrO2 coating was applied on long-length Stainless-Steel tapes using a non-vacuum reel-to-reel sol-gel dip coating technique. The thicknesses of coatings 7, 12 and 15 μm for 4, 8...

  • Stainless Steel Coatings Provide Scratch-Resistant Finish.  // Welding Journal;Apr2005, Vol. 84 Issue 4, p24 

    Introduces the STEEL IT anti-rust stainless steel coatings from Stainless Steel Coatings Inc. Product features; Industrial applications; Product availability.

  • Effect of Process Parameters on Friction Surfaced Coating Dimensions. Akram, Javed; Prasad Rao Kalvala; Misra, Mano // Advanced Materials Research;2014, Issue 922, p280 

    Friction surfacing is a novel technology to build corrosion and wear resistant coatings and build functionally graded metallic layers. In this work, the coating dimensions as affected by process parameters and high temperature strength of consumable rods have been compared. Friction stir welding...

  • Resistance to Corrosion of Zirconia Coatings Deposited by Spray Pyrolysis in Nitrided Steel. Cubillos, G.; Olaya, J.; Bethencourt, M.; Cifredo, G.; Blanco, G. // Journal of Thermal Spray Technology;Oct2013, Vol. 22 Issue 7, p1242 

    Coatings of zirconium oxide were deposited onto three types of stainless steel, AISI 316L, 2205, and tool steel AISI D2, using the ultrasonic spray pyrolysis method. The effect of the flux ratio on the process and its influence on the structure and morphology of the coatings were investigated....

  • A functional fluoropolymer powder coating for chemical process applications. Kosar, W. P.; Morris, S. // Journal of Coatings Technology & Research;Mar2007, Vol. 4 Issue 1, p51 

    Copolymers of vinylidene fluoride and hexafluorupropylene are well known for their chemical resistance and high purity. Extruded piping, molded parts, and sheet linings find extensive use in chemical process applications. A new powder coating has been developed which is based on this copolymer...


Read the Article


Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics