Microstructure-Property Relationships in HAz of New 13% Cr Martensitic Stainless Steels

Akselsen, O. M.; Rørvik, G.; Kvaale, P. E.; van der Eijk, C.
May 2004
Welding Journal;May2004, Vol. 83 Issue 5, p160-S
Examines the microstructure properties of new low-carbon, chromium martensitic stainless steels. Technique use to study the relationship between thermal characteristics and the heat-affected zone; Assessment of the mechanical properties of weld simulated specimens; Transformation behavior of martensitic stainless steels; Dependency of the heat-affected zone hardness level on the steel's chemical composition and the weld thermal program.


Related Articles

  • Yield strength enhancement of martensitic steel through titanium addition. Xu, L.; Shi, J.; Cao, W. Q.; Wang, M. Q.; Hui, W. J.; Dong, H. // Journal of Materials Science;May2011, Vol. 46 Issue 10, p3653 

    Yield strength enhancement for martensitic steel fabricated by vacuum induction melting is investigated. It is found that the addition of Ti can improve the yield strength property of the martensitic steel, which can be attributed to increase in precipitation hardening from formation of TiC...

  • Effect of High-Gradient Directional Crystallization on the Structure and Mechanical Properties of Corrosion-Resistant Nitrogen-Bearing Martensitic Steel 08Kh14AN4MDB. Bannykh, O. A.; Kablov, E. N.; Blinov, V. M.; Bondarenko, Yu. A.; Kostina, M. V.; Afanas'ev, I. A. // Metal Science & Heat Treatment;Sep/Oct2004, Vol. 46 Issue 9/10, p405 

    A comparative study of the structure and properties of corrosion-resistant nitrogen-bearing martensitic steel 08Kh14AN4MDB produced by methods of high-gradient directional crystallization (HGDC) and traditional crystallization is performed. The method of HGDC ensures considerable disintegration...

  • Features of Formation of the Structure and Properties of Chromium Corrosion-Resistant Steels Alloyed with Nitrogen. Rodionova, I.; Baklanova, O.; Udod, K.; Shaposhnikov, N.; Mel'nichenko, A. // Metallurgist;Jan2016, Vol. 59 Issue 9/10, p904 

    Chromium corrosion-resistant steels alloyed with nitrogen are studied by experiment. It is shown that depending on chemical composition and production parameters the steel's structure may be martensitic with a minimum residual austenite content, martensitic with a higher residual austenite...

  • Characteristics of the Rough-Cut Surface of Quenched and Tempered Martensitic Stainless Steel Using Wire Electrical Discharge Machining. Huang, C. A.; Tu, G. C.; Yao, H. T.; Kuo, H. H. // Metallurgical & Materials Transactions. Part A;Apr2004, Vol. 35 Issue 4, p1351 

    This article studies the surface characteristics of quench- and temper-treated AISI 440A martensitic stainless steels, which were rough cut using wire electrical discharge machining (WEDM). The microstructure of the recast layer on the cut surface was investigated using scanning and transmission...

  • Decomposition of YTiO Particles in 8 Pct Cr Oxide-Dispersion-Strengthened Martensitic Steel during Tempering. Tamura, M.; Sakasegawa, H.; Shiba, K.; Tanigawa, H.; Shinozuka, K.; Esaka, H. // Metallurgical & Materials Transactions. Part A;Aug2011, Vol. 42 Issue 8, p2176 

    Chemical composition analysis using inductively coupled plasma spectroscopy and phase identification using X-ray were performed on the extracted residues of 8 pct Cr martensitic steel strengthened by nanoscaled complex oxides, which consist of yttrium, titanium, and oxygen. Some YTiO particles,...

  • Fatigue Life Analysis of High Performance Motorcycle Disc Brake. Sahroni, Taufik Roni; Yong Sze Yeau; Widodo, W. Sapto; Bakar, Baharudin Abu; Sivaraos; Md Ali, Mohd Amran; ShahirKasim, Mohd // Applied Mechanics & Materials;2014, Vol. 699, p354 

    This paper presents fatigue life analysis of high performance motorcycle disc brake. The design parameter such as stress, deformation and safety factory that influences the disk brake on a high performance motorcycle were investigated. The simulation of static structural analysis of high...

  • Strengthening and Toughening Mechanisms in Martensitic Steel. KENNETT, Shane C.; FINDLEY, Kip O. // Advanced Materials Research;2014, Issue 922, p350 

    Low carbon martensitic steels are often produced by reaustenitizing and quenching (RA/Q). Direct quenching (DQ) has gained interest in the past few decades and requires quenching immediately after working above or below the austenite recrystallization temperature to form martensitic...

  • Structural heredity in low-carbon martensitic steels. Yugai, S. S.; Kleiner, L. M.; Shatsov, A. A.; Mitrokhovich, N. N. // Metal Science & Heat Treatment;Nov/Dec2004, Vol. 46 Issue 11/12, p539 

    The reason for the development of low-carbon martensitic steels (LCMS) is the absence of universal and comparatively inexpensive structural iron alloys combining high mechanical properties with processibility. Hardening of LCMS commonly includes heating aboveAc3 (930 - 950°C) and air-cooling....

  • Carbide Formation During Precipitation Hardening of SS440C Steel. Salleh, S. H.; Omar, M. Z.; Syarif, J.; Abdullah, S. // European Journal of Scientific Research;Jul2009, Vol. 34 Issue 1, p83 

    SS440C martensitic stainless steel been extensively used in automotive applications such as ball bearing, valve components, races and many other automotive components. Heat treatment processes such as precipitation hardening will greatly affect the microstructure and the mechanical properties of...


Read the Article


Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics