TITLE

Voltage gain effect in a ring-type magnetoelectric laminate

AUTHOR(S)
Dong, Shuxiang; Li, J. F.; Viehland, D.
PUB. DATE
May 2004
SOURCE
Applied Physics Letters;5/24/2004, Vol. 84 Issue 21, p4188
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
It has been observed that a ring-type magnetoelectric laminate composite of circumferentially magnetized magnetostrictive Tb1-xDyxFe2 and circumferentially polarized piezoelectric Pb(Zr,Ti)O3 layers has a large magnetoelectric voltage gain effect, offering potential in high-power miniature transformer applications. © 2004 American Institute of Physics.
ACCESSION #
13077535

 

Related Articles

  • Voltage-Divider Errors. Huster, Dean // Poptronics;Nov2002, Vol. 3 Issue 11, p39 

    Points out voltage-divider errors. Tolerance of the voltage output of a divider using series resistors; Example of a simple two-resistor divider typically used to increase the range of a digital panel meter; Mouser Electronics' sale of resistors with tolerances for critical applications.

  • Simple VCOM adjustment uses any logic-supply voltage. Khairolomour, Peter; Li, Alan // EDN;9/30/2004, Vol. 49 Issue 20, p96 

    This article describes a simple way in using any available logic supply to power the potentiometer providing the VCOM adjustment. All thin-film-transistor liquid crystal display panels require at least one appropriately tuned VCOM signal to provide a reference point for the panel's backplane....

  • Reduce voltage-reference output noise by half. Saab, Alfredo H.; Logan, Steve // EDN;2/3/2005, Vol. 50 Issue 3, p88 

    This article describes how to reduce low-frequency noise generated by an integrated circuit voltage reference. In theory, adding a lowpass filter to a reference's output reduces noise. In practice, a lowpass filter for suppression of noise frequencies below 10 Hz requires large values of series...

  • TRIMMING GETS ULTRA-PRECISE WITH MEMS-BASED PASSIVE RESISTORS. Allan, Roger // Electronic Design;6/21/2004, Vol. 52 Issue 14, p46 

    This article reports that resistor trimming is the most common method of optimizing sensor circuit performance for both discrete and monolithic IC sensors. It helps compensate for component tolerances, manufacturing variations, and the effects of temperature and aging. Typically, trimming is...

  • Resistors keep their cool, even when the system doesn't. Schweber, Bill; Granville, Fran // EDN;9/1/2005, Vol. 50 Issue 18, p22 

    This article features chip resistors, voltage dividers and resistor networks from the IRC Division of TT Electronics which meet the critical specifications over the -65 to +200 degrees centigrade range. The PCFD-HT SMT voltage dividers come in a 1206 package, and the tantalum-nitrogen-film-based...

  • Fixed DC-DC Regulator Output Uses A Digitally Controlled Potentiometer. Schmitz, Tamara; Kurtsevoy, Yuriy // Electronic Design;10/1/2009, Vol. 57 Issue 20, p21 

    The article provides an overview on the efficiency of the digitally controlled potentiometers (DCPs). It states that DCPs can provide advantages in remote operation and programmability, higher resolution, and increased reliability. It offers information on the design of a regulator that can be...

  • Trimmable Resistor Divider Improves Precision, TC Performance. Frostholm, Bob // Electronic Design;8/12/2010, Vol. 58 Issue 10, p65 

    The article provides ideas for the design of a trimmable resistor divider that improves precision and performance of temperature coefficient (TC) of voltage references. It offers tips on how to reduce errors which are deviations of the actual output voltage from desired specifications. A diagram...

  • PRECISION RESISTOR DIVIDES, CONQUERS HIGH VOLTAGES. Schweber, Bill // EDN;9/25/2003, Vol. 48 Issue 21, p18 

    Introduces the high-voltage values divider networks from Caddock Electronics aimed at analog applications. Ratio-temperature coefficient for the dividers; Voltage variations of the dividers; Price.

  • Simple fixture statically tests programmable-gain amplifiers. Štofka, Marián // EDN;6/26/2008, Vol. 53 Issue 13, p79 

    The article discusses a simple fixture which statically tests programmable-gain amplifiers. It describes a circuit comprised of a handful of components, which allows one to perform his own, independent testing of basic properties of digitally gain-programmable amplifiers. The evaluation...

Share

Read the Article

Courtesy of THE LIBRARY OF VIRGINIA

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics