TITLE

Optimization of Control Gains in Numerical Control

AUTHOR(S)
Hideki Aoyama; Duo Zhang
PUB. DATE
May 2015
SOURCE
Advanced Materials Research;2015, Vol. 806, p651
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
It is frequently the case that the feed rate indicated in a numerical control (NC) program does not obtain in actual machining processes and the cutting tool does not path the points indicated in the NC. A reason underlying such problems is that control gains are not optimized, which causes issues with acceleration and deceleration in the control of machine tools. To address these problems, in this paper, we propose a method for the optimization of control gains using the MATLAB and Simulink software by considering the weight of the workpiece, the controlling distance, and the controlling speed. Simulations confirmed the effectiveness of our proposed optimization.
ACCESSION #
110788118

 

Related Articles

  • Optimal Design Based on Dynamic Characteristics and Experimental Implementation of Submersible Electromagnetic Actuators. Baoping Cai; Yonghong Liu; Abulimiti, Aibaibu; Renjie Ji; Yanzhen Zhang; Xin Dong; Yuming Zhou // Strojniski Vestnik / Journal of Mechanical Engineering;2013, Vol. 59 Issue 7/8, p473 

    An optimization procedure based on the dynamic characteristics of a submersible electromagnetic actuator constrained in a specific volume has been developed. In order to achieve the minimum response time and low vibration when the actuator is opened, five radial dimensions are optimized when the...

  • An Acceleration Slip Regulation Strategy for Four-Wheel Drive Electric Vehicles Based on Sliding Mode Control. Hongwen He; Jiankun Peng; Rui Xiong; Hao Fan // Energies (19961073);Jun2014, Vol. 7 Issue 6, p3748 

    This paper presents an acceleration slip regulation (ASR) system for four-wheel drive (4WD) electric vehicles, which are driven by the front and rear axles simultaneously. The ASR control strategy includes three control modes: average distribution of inter-axle torque, optimal distribution of...

  • Vehicle Level Tip-to-Tail Modeling of an Aircraft. Roberts, Rory A.; Eastbourn, Scott M. // International Journal of Thermodynamics;Jun2014, Vol. 17 Issue 2, p107 

    A system-level multidisciplinary aircraft model has been developed exclusively in MATLAB/Simulink. Aircraft subsystem models representing the air vehicle system, propulsion system, robust electrical power system, thermal management systems, actuation system and their associated controllers were...

  • Optimization of Control Gains in Numerical Control. Hideki Aoyama; Duo Zhang // Advanced Materials Research;2016, Vol. 1136, p651 

    It is frequently the case that the feed rate indicated in a numerical control (NC) program does not obtain in actual machining processes and the cutting tool does not path the points indicated in the NC. A reason underlying such problems is that control gains are not optimized, which causes...

  • Designs and Optimizations of Active and Semi-Active Non-linear Suspension Systems for a Terrain Vehicle. Lajqi, Shpetim; Pehan, Stanislav // Strojniski Vestnik / Journal of Mechanical Engineering;2012, Vol. 58 Issue 12, p732 

    This paper introduces a design and optimization procedure for active and semi-active non-linear suspension systems regarding terrain vehicles. The objective of this approach is the ability to quickly analyze vehicles' suspension performances resulting from passive, active, or semi-active...

  • Four Quick Steps to Production: Using Model-Based Design for Sotware-Deined Radio. Donovan, Mike; Cozma, Andrei; Di Pu // Analog Dialogue;Nov2015, Vol. 49 Issue 11, p1 

    The article discusses how to detecting Mode S Extended Squitter, waveform and signal through software MATLAB and Simulink.

  • Four Quick Steps to Production: Using Model-Based Design for Software-Defined Radio. Donovan, Mike; Cozma, Andrei; Pu, Di // Analog Dialogue;Dec2015, Vol. 49 Issue 12, p1 

    The article offers four steps on how to produce a working receiver design that runs on Zynq SDR rapid prototyping platform using MATLAB and Simulink to develop algorithm that successfully process and decde ADS-B transmissions.

  • Apps make software design tools more user-friendly.  // Electronics Weekly;9/19/2012, Issue 2520, p6 

    The article focuses on the software updates of MatLab and Simulink from MathWorks Inc.

  • An Experimentation on Anti-Reset Windup Scheme for Level Process Station. Thirunavukkarasu, I.; Fareed Abuaiah, Mohammed Ibrahim; George, V. I.; Shanmuga Priya, S. // Sensors & Transducers (1726-5479);Dec2012, Vol. 147 Issue 12, p87 

    This paper represents how to eliminate the undesired effect occurred in the PI or PID controller called integrator-windup by using four different methods. These different methods are known as anti-windup strategies. A Simulink-Matlab program has been used to investigate the results and the...

Share

Read the Article

Courtesy of NEW JERSEY STATE LIBRARY

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics