TITLE

Effect of association of sugarcane bagasse with Eucalyptus wood on the quality of particleboard

AUTHOR(S)
Laís Farrapo, Camila; Farinassi Mendes, Rafael; Wisky Silva, Danillo; Mendes, Lourival Marin; Soares Scolforo, José Roberto; Guimarães Jr., José Benedito
PUB. DATE
March 2016
SOURCE
Key Engineering Materials;2016, Vol. 668, p341
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
Particleboard industries, which are progressively increasing in number, consume a significant amount of wood from planted forests, mainly from the Pinus and Eucalyptus genera. However, these panels can be produced from any lignocellulosic material that provides high mechanical strength and good physical characteristics. Accordingly, the waste generated by the Brazilian agribusiness industry is an alternative resource for manufacturing particleboards. The study aimed to evaluate the effect of the combination of sugarcane bagasse and eucalyptus wood on the physical and mechanical properties of particleboards. The panels were produced with sugarcane bagasse in the proportion of 0, 25, 50, 75, and 100% supplemented with E. urophylla. The panels were produced with 9% urea-formaldehyde adhesive, nominal density of 0.70 g/cm3, and with the pressing cycle of 160°C temperature, specific pressure of 3.92 MPa, and operation time of 8 min. The significance of the proportion of sugarcane bagasse on all physical and mechanical properties was evaluated. The panels with the combination of wood with sugarcane bagasse showed the lowest values in the physical properties and the highest values in the mechanical properties. Only panels prepared with 25% and 50% sugarcane bagasse met all the requirements of the marketing standards.
ACCESSION #
110377675

 

Related Articles

  • FEASIBILITY OF USING MDP PANELS, COMPARED TO CONVENTIONAL PARTICLEBOARDS. Ribeiro Guimarães, Bárbara Maria; Guimarães Junior, José Benedito; Barbosa Campomori, Jefferson; Farinassi Mendes, Rafael; Marin Mendes, Lourival // Key Engineering Materials;2016, Vol. 668, p145 

    The objective of this study was to investigate, by physical properties, the efficiency of MDP panels, compared to conventional particleboards, since MDP was considered as a raw material for the manufacture of these panels. MDP panels had the following composition: 20/60/20 face/core; a...

  • Thermal insulation particleboards made with wastes from wood and tire rubber. da Silva Bertolini, Marília; Luis Christoforo, André; Rocco Lahr, Francisco Antonio // Key Engineering Materials;2016, Vol. 668, p263 

    The concept of sustainable buildings addresses the environmentally efficiency, with respect to energy consumption, by adopting products that offer thermal insulation. Moreover, use of wastes from different materials also contributes to obtain products for this application. The volume of wastes...

  • EVALUATION OF PHYSICAL PROPERTIES OF PARTICLEBOARD PRODUCED FROM SUGARCANE LEAVES. Hoffmamm Martins, Evelyn; Benedito Guimarães Junior, José; de Paula Protásio, Thiago; Farinassi Mendes, Rafael; Ribeiro Guimarães, Bárbara Maria // Key Engineering Materials;2016, Vol. 668, p270 

    The southwest region of the state of Goiás stands out for agriculture, especially the production of grain and sugarcane. This high agricultural production has a result of generation of agroindustrial waste and it has a high potential to be exploited for particleboard manufacturing. In this...

  • Use of waste wood for particleboard production. de Lima Felix, Adriele; Pinto Narciso, Carolina Rezende; Silveira Lima, Fernanda; Farinassi Mendes, Rafael; Marin Mendes, Lourival; Soares Scolforo, José Roberto // Key Engineering Materials;2016, Vol. 668, p375 

    In parallel with the growing demand for lumber, there has been an increase in the amount of waste generated by this industry, such as chips, shavings, and sawdust as the main waste. Such wastes are disposed in unsuitable locations or burned for energy generation. The present study aimed to...

  • Dimensional stability of particleboards produced with soybean residue. Benedito Guimarães Jr., José; Luz Guimarães, Ingrid; Nogara Lisboa, Fernando Jesus; Farinassi Mendes, Rafael; Ribeiro Guimarães, Bárabara Maria // Key Engineering Materials;2016, Vol. 668, p399 

    The southwest region of Goiás is a major grain producer in the country, with emphasis on soybeans. It is protected by a pellicle grain into a legume. After its separation, the film is eventually discarded or used as animal feed. One alternative is the production of particleboards, considering...

  • Functionally graded MDP panels using bamboo particles. Teodoro, Raquel; Raabe, Joabel; Silva, Danillo Wisky; Mendes, Rafael Farinassi; Mendes, Lourival Marin; Denzin Tonoli, Gustavo Henrique // Key Engineering Materials;2016, Vol. 668, p39 

    MDP (medium density particleboard) panels are normally graded in composition along their cross-section, using low-size particles and high concentration of adhesive on the particleboard surface (leading to improved physical and mechanical properties), and high-size particles in the particleboard...

  • Study of the potential employment of Malvaceae Species in composites materials. Gama Guimarães, Bárbara Maria; Cayuela Marín, Diana; Fernando Zonatti, Welton; Mantovani, Waldir; Relvas, Cátia; Cunha, Fernando; Fangueiro, Raul; Savastano Júnior, Holmer; Baruque-Ramos, Júlia // Key Engineering Materials;2016, Vol. 668, p75 

    The employ of vegetal fibers for textiles and composites represents a great potential in economic and social sustainable development. Some Malvaceae species are considered tropical cosmopolitans, such as from Sida genus. Several species of this genus provide excellent textile bast fibers, which...

  • Synthesis Of Silver Nanoparticles With Potential Antifungical Activity For Bamboo Treatment. Pandoli, Omar; Ventura Pereira-Meirelles, Fatima; Lobo Lobo Luz, Eric Monteiro; Assumpção, Aline; dos Santos Martins, Raquel; del Rosso, Tommaso; Ghavami, Khosrow // Key Engineering Materials;2016, Vol. 668, p86 

    To increase the durability of bamboo it is important to find an easy method to fill the micro and meso structure of the biological matrix using a nano-structural material with an anti- fungical activity. A colloidal solution of silver nanoparticle (Ag-NPs) is a dispersion of metal nanoparticle...

  • Sheath bamboo leaves used at high pressure architect. GARCIA, Juliana; JOHN, Vanderley // Key Engineering Materials;2016, Vol. 668, p92 

    Sheath bamboo leaves (SBL) are potential lignocelluloses waste, aimed to produce laminated architectonic coatings. In this work was studied the surface interaction among the SBL and three types of adhesive: Polyvinyl Acetate (PVAc), Castor oil Polyurethane Adhesive bi- component (Vegetal PU),...

Share

Read the Article

Courtesy of THE LIBRARY OF VIRGINIA

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics