TITLE

The Analysis of Tool Wear in Milling CFRP with Different Diamond Coated Tool

AUTHOR(S)
Xiaofan Yang; Yousheng Li; Guohong Yan; Judong Liu; Dongmin Yu
PUB. DATE
January 2016
SOURCE
Key Engineering Materials;2016, Vol. 667, p231
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
Carbon fiber-reinforced plastics (CFRP) are typical difficult-to-machine materials, which is easy to produce many defects such as burrs, dilacerations, layering in milling process. And selecting the appropriate cutting tool has become the key to machining CFRP with high quality and efficiency. In the paper, the machining principle of milling CFRP with new type end mill was analyzed. The diamond coating of general right-hand end mill, cross-flute router and fine-cross-nick router were used to cutting CFRP under the same cutting condition. Through the comparative analysis of the workpiece's surface quality and tool wear, it concluded that: compared with right-hand diamond coated end mill, cross-flute diamond coated router or fine-cross-nick diamond coated router could effectively suppress the appearance of burrs and dilacerations; abnormal coating peeling appeared in the flank face of right-hand diamond coated end mill, forming the boundary wear, which accelerated wear failure; the flank wear of diamond coated cross-flute router and fine-cross-nick router were both abrasive wear. Due to having more cutting edge than cross-flute router in cutting process, the flank wear of fine-cross-nick router was slower, and the tool life was longer. So it was more suitable for cutting CFRP.
ACCESSION #
110337502

 

Related Articles

  • Composite strategies.  // MWP;Sep2012, p46 

    The article reports on the move of Kennametal Inc. to look at fundamental themes, including classification of carbon-fiber-reinforced polymer (CFRP) materials. It states that the company faces challenges over delamination and service life, indicating that machining composites has no chips and...

  • Modeling and simulation of the machining of unidirectional CFRP. Pecat, Oliver; Rentsch, RĂ¼diger; Garbrecht, Martin; Brinksmeier, Ekkard // Advanced Materials Research;2014, Issue 907, p55 

    The machining process of carbon fiber reinforced plastics is very complex due to its inhomogeneous material structure and anisotropic properties. Experimental investigation can be very demanding and time consuming because of the different fiber/matrix compositions and the influence of the fiber...

  • Study on Resin Infusion Behavior of the CFRP Integrated Manufacturing Process Based on RFI Process. Yuqin Guo; Zhao Meng; Minhang Sun; Fuzhu Li; Wei Chen // Advanced Materials Research;2014, Vol. 941-944, p1243 

    In the CFRP integrated manufacturing process based on RFI process, a CFRP stacking sheet is fabricated by laying alternatively Carbon Fiber Fabrics on Epoxy Resin Films each other. So its infusion process can be regarded as a concurrent infusion system consisting of some representative infusion...

  • Reinforced Building to Fend Off Attacks.  // USA Today Magazine;Jun2011, Vol. 139 Issue 2793, p15 

    The article reports that assistant professor Sarah Orton of the University of Missouri in Columbia, Missouri is working with the U.S. Army to test a method of retrofitting buildings with carbon fiber reinforced polymer (CFRP) to protect them in case of a terrorist attack.

  • Electricity and Carbon Fiber Offer Building Protection.  // Buildings;Jun2011, Vol. 105 Issue 6, p20 

    The article offers information on technologies for the protection of properties, including carbon fiber reinforced polymer (CFRP) and electrical currents.

  • Teijin's CFRTP components pilot plant hums.  // Indian Textile Journal;Mar2013, Vol. 123 Issue 6, p96 

    The article focuses on the operation of the carbon fibre reinforced thermoplastic (CFRTP) components pilot plant of Teijin Ltd. located Matsuyama Factory in Ehime Prefecture, Japan.

  • One-minute carbon-fiber composite cycle time reported.  // Composites Technology;Apr2011, Vol. 17 Issue 2, p14 

    The article reports that Tokyo, Japan-based Teijin Ltd. has set up a mass-production technology for carbon fiber-reinforced plastic (CFRP).

  • Carbon fiber-reinforced plastics based on epoxy resin toughened with core shell rubber impact modifiers. Park, Hyeongcheol; Jung, Hana; Yu, Jaesang; Park, Min; Kim, Seong Yun // e-Polymers;Nov2015, Vol. 15 Issue 6, p369 

    The weak impact properties of carbon fiber-reinforced plastics (CFRPs) are due to their laminated structure, thus limiting the use of these materials in various automotive applications even though they provide weight savings as compared with metal materials. In this study, core shell rubbers...

  • RTP Company Introduces Series of Carbon Fiber Reinforced Thermoplastic Compounds.  // Electronics Protection;Spring2014, Vol. 12 Issue 1, p4 

    The article offers brief information on a series of carbon fiber reinforced thermoplastic compounds released by RTP Co.

Share

Read the Article

Courtesy of THE LIBRARY OF VIRGINIA

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics