TITLE

Comparative study on the behavior of Crushed and Rolled Sustainable Concrete Materials based on new generation of Superplasticizer at Curing Temperature

AUTHOR(S)
BELLA, Ilham Aguida; ASROUN, Aîssa; BELLA, Nabil
PUB. DATE
March 2016
SOURCE
International Journal of Engineering Research in Africa;2016, Vol. 19, p1
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
The aggregates factory consumes a big quantity of energy; by consequence, it costs money, in the other hand it produces a lot of waste material or SCM (sustainable concrete material). The main aspects which guide this study is the current tendency to make mortar based on a very abundant material which are crushed limestone aggregates and naturals dunes sand. The results obtained in this study summarize up the importance of SCMs aggregates on behavior of the mortar, this different kind of SCM aggregate offered different behavior at the fresh state of the batch and by consequence its result with different mechanical behavior at the hardened state of mortar. This study focus also on the behavior of the new kind of chemical admixture, which is acrylic superplasticizer. The principal aim of adding rolled or crushed SCM is makes a mortar, which can resist to exhaustive environment (at curing temperature).
ACCESSION #
110337452

 

Related Articles

  • PRECIPITATION HARDENING ANALYSIS OF AN AI-8%Ag ALLOY. Martínez, Sergio Eliseo Hernández; Rocha, Jorge García; de Jesús Cruz Rivera, José; Rivera, José Luis Hernández // Advanced Materials Research;2014, Vol. 976, p154 

    Aluminum alloys are important in aerospace industry, due to their mechanical properties, low specific weight and good corrosion resistance. Such properties are achieved due to a heat treatment of solubilization, quenching and aging, in order to precipitate metastables phases, which act as...

  • Plastic slip patterns through rate-independent and rate-dependent plasticity. Lancioni, Giovanni; Yalcinkaya, Tuncay // Key Engineering Materials;2014, Vol. 611-612, p1777 

    Plastic deformation induces various types of dislocation microstructures at different length scales, which eventually results in a heterogeneous deformation field in metallic materials. Development of such structures manifests themselves as macroscopic hardening/softening response and plastic...

  • Entire Hardening of Small Thin Plate with a Small Power Semiconductor Laser Considering Plate Deformation. Ryosuke ODA; Toshiki HIROGAKI; Eiichi AOYAMA; Keiji OGAWA // Advanced Materials Research;2014, Issue 1017, p636 

    Nowadays, resource saving technologies have become important because of increasing global environmental problems. Moreover, demand is increasing for the manufacturing and machining of small mechanical parts because of the downsizing of electronic mobile devices. Thus, one requirement has emerged...

  • Efficient Method for Optimizing Calcium Silicate Masonry Unit Manufacturing Using Simulation-Based Optimization and Decomposition. Donhauser, Toni; Lohse, Joachim; Franke, Jörg; Schuderer, Peter // Applied Mechanics & Materials;2017, Vol. 856, p99 

    This paper describes a holistic, simulation-based optimization approach to control plant operations for manufacturing calcium silicate masonry units (CS). Starting from an investigation and classification of the CS production, specific target criteria are derived. To enable the influencing of...

  • Use of Cup Technology to Strengthen the Beds of Buildings and Structures by Hydrofracking. Voznesenskaya, E.; Ermolaev, V.; Osokin, A.; Tatarinov, S. // Soil Mechanics & Foundation Engineering;Jan2015, Vol. 51 Issue 6, p299 

    Results are cited for investigations based on a set of optimal parameters of cement-grout injection for strengthening of a soil mass with use of cup technology during hydrofracking. It is shown that the method of multiple injection in each horizon of the soil mass contributes to more effective...

  • Dealing with Lifters. Kerkstra, Randy // Plastics Technology;Nov2015, Vol. 61 Issue 11, p32 

    The article discusses lifters as a cause for molding issues or failures. Topics discussed include reducing sticking and dragging problems, lifter pre-load as a critical specification (spec), and the method for pushing down below cavity surface lifter or detail. Also discussed are maintenance...

  • Mechanical Properties and Deformation Behavior of Bulk Metallic Glasses. Louzguine-Luzgin, Dmitri V.; Louzguina-Luzgina, Larissa V.; Churyumov, Alexander Yu. // Metals (2075-4701);Mar2013, Vol. 3 Issue 1, p1 

    Metallic glasses demonstrate unique properties, including large elastic limit and high strength, which make them attractive for practical applications. Unlike crystalline alloys, metallic glasses, in general, do not exhibit a strain hardening effect, while plastic deformation at room temperature...

  • Approximation of the Norton--Hoff plasticity model with isotropic hardening through Cosserat plasticity. BIES, P. M. // Archives of Mechanics;2014, Vol. 66 Issue 1, p37 

    IN THIS PAPER THE REGULARIZING PROPERTIES of Cosserat elasto-plastic models in a geometrically linear setting are investigated. For vanishing Cosserat effects it is shown that the Norton--Hoff model with isotropic hardening is approximated by the model with microrotations.

  • Calibration of Hardening Rules for Cyclic Plasticity. Rezaiee-Pajand, M.; Sinaie, S. // International Journal of Engineering (1025-2495);Apr2013, Vol. 26 Issue 4, p351 

    In the realm of multi-axial ratcheting, a step by step mathematical approach is developed for the parameter determination of decomposed kinematic hardening rules. For this purpose, key characteristics are mathematically derived for these hardening rules under multi-axial loading. Then, these...

Share

Read the Article

Courtesy of THE LIBRARY OF VIRGINIA

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics