TITLE

Motor Efficiency: Sneaky Realities

AUTHOR(S)
Stockman, Mike
PUB. DATE
October 2015
SOURCE
National Driller;Oct2015, Vol. 36 Issue 10, p14
SOURCE TYPE
Trade Publication
DOC. TYPE
Article
ABSTRACT
The article focuses on selecting best pump and control/drive for pumping machinery, that help in decreasing the challenge of installing the efficient system for customers.
ACCESSION #
109938289

 

Related Articles

  • Blackmer extends warranty on sliding vane pumps.  // Fleet Owner Blog;11/8/2012, p1 

    The article reports Blackmer's move in extending its warranty period for the TXD Series of sliding vane transport pumps to 60 months from installation or 66 months from purchase, and its Performance Assurance to two years from installation or 30 months from purchase.

  • Create a roadmap for proper pump maintenance. Eiler, Karl // Plant Engineering;Jul2008, Vol. 62 Issue 7, p55 

    The article provides tips for the proper pump maintenance in the U.S. According to the article, the installation and operation manual for proper pump startup should be followed in detail because it provides the sound foundation for optimum pump operation. Thus, this preventive maintenance event...

  • Make your center pivot more efficient with just 8 steps.  // Nebraska Farmer;Nov2012, Vol. 154 Issue 11, p40 

    The article offers tips for the reduction of pumping costs and for the improvement of the system's overall performance such as checking sprinkler installation, checking system capacity, and checking pivot pressure.

  • Determining the sealing element parameters for the outlet gland of a deep-pumped installation. Abbasov, E.; Kakhramanov, Kh. // Chemical & Petroleum Engineering;Nov2008, Vol. 44 Issue 11/12, p715 

    The effects are considered of sealing element (SE) parameters on the performance of the output gland for a deep-pumped installation. Tests have been done on this type of SE. A theoretical basis is provided for the economic performance of the proposed SE. A sealing criterion is considered for the...

  • mailbag: Are Split Mechanical Seals the Solution? Bachus, Larry // Flow Control;Jun2012, Vol. 18 Issue 6, p42 

    A letter to the editor and response from the editor is presented related to installation and maintenance of pump problems.

  • PUMP WISE. Herman, Eric // Aqua;Jan2012, Vol. 37 Issue 1, p69 

    The article shares the author's tips in selecting and installing pumps and motors for residential systems. One is to consider the pump performance curve because the basic sizing exercise will indicate the selection of small pumps. Another is to consider the advent of variable frequency drive...

  • Rules of Thumb for Bilge Pump Installations.  // Practical Sailor;Oct2010, Vol. 36 Issue 10, p30 

    The article presents tips on how sailors can install an electric bilge pump in their boat. The author recommends the installation of two electric centrifugal pumps so that there is always a back-up. Mid-size boats should install a 1,000 to 1,500 gallon-per-hour pump (GPH) for the primary pump...

  • YFC turns on the water. Relf, Tim // Farmers Weekly;8/8/2008, p83 

    The article reports that a group of 12 Young Farmers from Devon, England have just returned from Tanzania where they installed a water pump for the Livestock Training Institute near Arusha. They had teamed up with the Bicton Overseas Agricultural Trust to ensure running water was provided for...

  • Sheraton Vancouver Sustains Water Pressure with Grundfos Energy-Efficient Booster.  // Canadian Consulting Engineer;May2013, Vol. 54 Issue 3, p37 

    The article presents a case study of a multi-pump controller (MPC) BoosterpaQ system that is a water pump installed at the Sheraton Wall Centre hotel in Vancouver, British Columbia. It mentions that the MPC consists of 3 CR vertical inline multistage pumps that can be used for variable speed...

Share

Read the Article

Courtesy of THE LIBRARY OF VIRGINIA

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics