TITLE

Mg-based bulk metallic glass composites with plasticity and high strength

AUTHOR(S)
Ma, H.; Xu, J.; Ma, E.
PUB. DATE
October 2003
SOURCE
Applied Physics Letters;10/6/2003, Vol. 83 Issue 14, p2793
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
Composite alloys of (Mg[sub 0.65]Cu[sub 0.075]Ni[sub 0.075]Zn[sub 0.05]Ag[sub 0.05]Y[sub 0.1])[sub 100-x]Fe[sub x](x=9 and 13) have been produced through copper mold casting, based on a good bulk metallic glass former. Upon cooling the melt, an α-Fe solid solution precipitates uniformly with sizes in the 1–10 μm range while the remaining melt undergoes a glass transition. The in situ composite has a compressive strength as high as ∼1 GPa, a factor of 1.6 higher than the single-phase metallic glass. In contrast to all the previous Mg-based monolithic glasses that always fail in the elastic regime, a plastic strain to failure of the order of 1% was obtained for the Fe-toughened composite. © 2003 American Institute of Physics.
ACCESSION #
10964896

 

Related Articles

  • Shear localization of nanoscale W in metallic glass composites. Min Ha Lee; Sordelet, Daniel J. // Journal of Materials Research;Feb2006, Vol. 21 Issue 2, p492 

    High-density tungsten/metallic glass composites were fabricated by warm extrusion of two different powders. The first powder was a physical blend of -45 µm tungsten and Hf-based metallic glass powders and produced a relatively coarse distribution of tungsten particles within a continuous...

  • Size-affected shear-band speed in bulk metallic glasses. Liu, Z. Y.; Yang, Y.; Liu, C. T. // Applied Physics Letters;10/24/2011, Vol. 99 Issue 17, p171904 

    In this letter, we report an important experimental finding and theoretical analysis of the shear-band speed measured in a variety of bulk metallic-glasses. Unlike the prior work, in which the shear-band speed was regarded as a constant, our current study, based on carefully designed...

  • Effect of frame stiffness on the deformation behavior of bulk metallic glass. Han, Z.; Li, Y.; Gao, H. J. // Journal of Materials Research;Oct2010, Vol. 25 Issue 10, p1958 

    It has been shown that the stability of shear banding and plasticity of bulk metallic glasses (BMGs) can be strongly influenced by the machine stiffness. Here, we demonstrated that the practice of adding a frame parallel to the sample is quantitatively equivalent to increasing the machine...

  • Temperature dependence of serrated flows in compression in a bulk-metallic glass. Jiang, W. H.; Jiang, F.; Liu, F. X.; Choo, H.; Liaw, P. K.; Qiu, K. Q. // Applied Physics Letters;12/25/2006, Vol. 89 Issue 26, p261909 

    The authors investigated the effect of temperature on the plastic-flow and shear-banding behaviors of a Zr-based bulk-metallic glass in compression. The results indicate that at a subambient temperature (194.5 K) the plastic deformation of the bulk-metallic glass is still inhomogeneous and is...

  • The Self-Organized Critical Behavior in Pd-based Bulk Metallic Glass. Zhong Wang; Jiaojiao Li; Wei Zhang; Junwei Qiao; Baocheng Wang // Metals (2075-4701);2015, Vol. 5 Issue 3, p1188 

    Bulk metallic glasses (BMGs) deform irreversibly through shear banding manifested as serrated-flow behavior during compressive tests. The strain-rate-dependent plasticity under uniaxial compression at the strain rates of 2 × 10-2, 2 × 10-3, and 2 × 10-4·s-1 in a Pd-based BMG is...

  • Free volume coalescence and void formation in shear bands in metallic glass. Wright, Wendelin J.; Hufnagel, T. C.; Nix, W. D. // Journal of Applied Physics;2/1/2003, Vol. 93 Issue 3, p1432 

    We have investigated the possibility of void nucleation from the coalescence of excess free volume generated in shear bands during deformation of the Zr[sub 41.2]T[sub 13.8]Cu[sub 12.5]Ni[sub 10.0]Be[sub 22.5] bulk metallic glass. Excess free volume in a shear band results in excess free energy...

  • Shear strength of epoxypolysulfone glass-reinforced plastics in a wide range of loading rates. Gorbatkina, Yu.; Solodilov, V.; Kuperman, A.; Pavlovskii, D.; Shustov, M. // Journal of Engineering Physics & Thermophysics;Sep2005, Vol. 78 Issue 5, p885 

    The shear strength of unidirectional epoxypolysulfone glass-reinforced plastics in the range of six decimal orders of loading rates has been measured. ED-22 epoxydiane resin (analog of DGEBA) modified by PSK-1 aromatic polysulfone served as a matrix. It has been shown that the strength values...

  • Bulk properties of composite media. I. Simplification of bounds on the shear modulus of suspensions of impenetrable spheres. Sen, Asok K.; Lado, F.; Torquato, S. // Journal of Applied Physics;11/1/1987, Vol. 62 Issue 9, p3503 

    Part I. Presents a study on third-order upper and lower bounds on the shear modulus of a model composite made up of equisized, impenetrable spherical inclusions randomly distributed throughout a matrix phase. Problem with the theoretical prediction of the effective properties of disordered...

  • Temperature dependent dynamics transition of intermittent plastic flow in a metallic glass. I. Experimental investigations. Liu, Z. Y.; Wang, G.; Chan, K. C.; Ren, J. L.; Huang, Y. J.; Bian, X. L.; Xu, X. H.; Zhang, D. S.; Gao, Y. L.; Zhai, Q. J. // Journal of Applied Physics;Jul2013, Vol. 114 Issue 3, p033520 

    Cooling shrinkage can increase the atomic packing density of metallic glasses, which can influence their elastic and plastic behaviour. In the present study, the compressive deformation behaviour of a Zr-based metallic glass at temperatures well below the glassy transition temperature, say 123 K...

Share

Read the Article

Courtesy of VIRGINIA BEACH PUBLIC LIBRARY AND SYSTEM

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics