TITLE

Plasticity in Ni[sub 59]Zr[sub 20]Ti[sub 16]Si[sub 2]Sn[sub 3] metallic glass matrix composites containing brass fibers synthesized by warm extrusion of powders

AUTHOR(S)
Bae, D. H.; Lee, M. H.; Kim, D. H.; Sordelet, D. J.
PUB. DATE
September 2003
SOURCE
Applied Physics Letters;9/22/2003, Vol. 83 Issue 12, p2312
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
Deformation behavior of centimeter-scale Ni-based metallic glass matrix composites reinforced by brass fibers, synthesized by warm extrusion of gas atomized powders, has been investigated under the uniaxial compression condition at room temperature. Throughout the extrusion process, all blended spherical powders are elongated along the extrusion direction. The brass fibers are well distributed in the metallic glass matrix for the metallic glass matrix composites containing the brass up to 0.4 in volume fraction and no pores are visible. With increasing the brass content, elastic modulus and strength decrease due to the softness of the brass, but enhanced macroscopic plasticity is observed due to the formation of multiple shear bands, initiated from the interface between brass fiber and metallic glass matrix, as well as their confinement between the brass fibers. These behaviors are not observed in the sample synthesized by warm extrusion of only metallic glass powders. © 2003 American Institute of Physics.
ACCESSION #
10848429

 

Related Articles

  • Full strength compacts by extrusion of glassy metal powder at the supercooled liquid state. Kawamura, Yoshihito; Kato, Hidemi // Applied Physics Letters;10/2/1995, Vol. 67 Issue 14, p2008 

    Reports the production of full strength compacts of metallic glass by warm extrusion of powders. Alloy used in the production of compacts; Temperature for maintaining the ductility of melt-spun alloy; Conduction of powder production and its consolidation in a closed powder metallurgy processing...

  • Design and analysis of streamlined extrusion die for round to hexagon using area mapping technique, upper bound technique and finite element method. Venkatesh, C.; Venkatesan, R. // Journal of Mechanical Science & Technology;May2014, Vol. 28 Issue 5, p1867 

    Extrusion is one of the most important metal forming process commonly used for the manufacturing of the hexagonal rods. Extrusion of metal through a conventional shear faced die experiences few practical limitations such as dead metal zone, more redundant work etc. Most of the research works...

  • Delayed shear banding and evolution of local plastic flow in a metallic glass. Sun, B. A.; Liu, Z. Y.; Yang, Y.; Liu, C. T. // Applied Physics Letters;9/1/2014, Vol. 105 Issue 9, p1 

    Metallic glasses (MGs) or other amorphous materials often yield macroscopically with the instantaneous formation of shear bands under the applied stresses. Here, through microcompression tests, we showed that, below the conventional yield stress, shear banding can still be activated but requires...

  • Free volume coalescence and void formation in shear bands in metallic glass. Wright, Wendelin J.; Hufnagel, T. C.; Nix, W. D. // Journal of Applied Physics;2/1/2003, Vol. 93 Issue 3, p1432 

    We have investigated the possibility of void nucleation from the coalescence of excess free volume generated in shear bands during deformation of the Zr[sub 41.2]T[sub 13.8]Cu[sub 12.5]Ni[sub 10.0]Be[sub 22.5] bulk metallic glass. Excess free volume in a shear band results in excess free energy...

  • Hot-Workability of Gamma-Based TiAI Alloys during Severe Torsional Deformation. Fröbel, U.; Appel, F. // Metallurgical & Materials Transactions. Part A;Aug2007, Vol. 38 Issue 8, p1817 

    Wrought TiAI products manufactured by conventional hot-working procedures, such as forging and extrusion, suffer from structural and chemical inhornogeneities, which are major concerns for the reliability of components. In an attempt to overcome these problems, TiAI alloys were hot worked by...

  • Texture development in two-pass ECAE-processed beryllium. Beyerlein, I.; Field, R.; Hartwig, K.; Necker, C. // Journal of Materials Science;Dec2008, Vol. 43 Issue 23/24, p7465 

    Texture development and substructure evolution are described for pure beryllium given two-pass equal channel angular extrusion (ECAE) processing following routes A and C. These routes impose different strain paths between the first and second passes—the former cross-shearing and the...

  • Charge Weld Effects on High Cycle Fatigue Behavior of a Hollow Extruded AA6082 Profile. Nanninga, N.; White, C.; Dickson, R. // Journal of Materials Engineering & Performance;Oct2011, Vol. 20 Issue 7, p1235 

    Fatigue properties of specimens taken from different locations along the length of a hollow AA6082 extrusion, where charge weld (interface between successive billets in multi-billet extrusions) properties and the degree of coring (accumulation of highly sheared billet surface material at back...

  • Dynamic Analysis of the Media in Centrifugal Barrel Finishing. ZHANG Jian-li; LI Wen-hui; YANG Sheng-qiang; Jiang Qian; Liu Li-ping // Advanced Materials Research;2014, Vol. 1027, p230 

    The main effects in centrifugal barrel finishing result from the impact of the mutual impacts, the interaction of extrusion, the rotation shear and the sliding force, it can't be calculated that the force created by the collision among the media and the velocity of the media at present. It is...

  • On Flow Layer Uniformity in the Co-Extrusion of Polymer Multilayer Film. Guo-Chiuan Tzeng; Ren-Haw Chen // Advanced Materials Research;2014, Issue 939, p381 

    In the multilayer co-extrusion process, two or more materials are simultaneously brought together and layered in a single extrusion process. When co-extruding two polymers with different rheological properties, uniformity control of the flow layer at and downstream of the confluence is vital for...

Share

Read the Article

Courtesy of VIRGINIA BEACH PUBLIC LIBRARY AND SYSTEM

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics